Corium Experiments; Pedestal Behaviors Using Lead

As part of the ongoing work to better understand how corium (melted reactor fuel) can behave after burning through the reactor vessel we have completed another set of experiments. SimplyInfo.org member Edano prepared and ran tests using lead as the melt material. Lead had been used to stand in for melted reactor fuel in some of the very early experiments at Brookhaven National Lab in the US. The previous set of experiments involved melted glass with a model of the reactor pedestal. That experiment was similar to what is understood about a rapid core melt and used a larger volume of material. Read about that experiment here. (pdf) It can also be viewed here as a web page: http://www.fukuleaks.org/web/?p=11930

The lead experiments used a clay pot as the pedestal with a clay saucer to represent the containment structure floor. This experiment used the minimum estimated core melt volume and converted it into a scaled down amount of lead. A tea mesh strainer was used to hold the lead above the pedestal as a rough stand in for the bottom head of the reactor vessel. The strainer was suspended over the pedestal using a piece of steel garden mesh to prevent contact with the pottery. The melt process was taken to 400c and held there for one hour. Corium minimum volume: 17.5 m³ Scaled down to 1:116 in lead: 125 g (11 ml) Melt height: 6 mm lead melt height translates to 70 cm real height About 20g of the lead volume stayed in the strainer due to oxidation and possible residue or coating on the lead pieces. More information about the process and results are inline among the images.

pedestal_Fig1 Calculations and documented sizes for the example BWR Mark 1 reactor based on Fukushima Daiichi unit 1. Corium volume based off of Sandia National Lab’s computer modeling of Fukushima Daiichi unit 1 meltdown progression.

pedestal_Fig4

The pottery examples superimposed over the Fukushima Daiichi unit 1 elevation drawing.  pedestal_Fig4a

The pottery examples superimposed over the Fukushima Daiichi unit 1 elevation drawing.

pedestal_Fig3Detail showing the downcomer structure between the containment drywell into the torus (wetwell). The right illustration details how the containment floor ties into the downcomer. This is the area of most concern for potential corium burn through.

pedestal_Fig2 Pedestal doorway calculations Photo of the unit 5 pedestal doorway under the reactor vessel at Fukushima Daiichi

 Diagram of BWR Mark 1 reactor vessel and pedestal cutaway.

SAM_0257 Configuration in the furnace with the strainer over the pedestal model.

SAM_0262 Lead fishing weights used for the lead melt. SAM_0263 Close up of the lead weights

SAM_0267 Furnace with the strainer in place.

SAMSUNG CAMERA PICTURES

 Temperature controller for the furnace during ramp up.

 

SAM_0266 Ceramic pedestal and saucer after the melt run. The lead mass can be seen trying to flow out the doorway of the pedestal.

SAM_0270

Strainer as it was held over the pedestal.

SAM_0272

Residue left in the strainer after the furnace run. Assumed to be oxides from the lead and residues that may have been used as a coating on the lead weights.

SAM_0275Underside of the strainer with melt residue.

SAM_0278 Overhead view of the pedestal after furnace run.

SAM_0266 Lead melt seen attempting to flow out of the pedestal, photo taken after the furnace run.  SAM_0281 Lead melt after cooling. Black line shows where the pedestal was located. The curved bulge where the lead attempted to exit the pedestal can be seen on this image. The lead melt did manage to move the pedestal slightly during the process. SAM_0284 Another view of the lead melt. The lead did manage to score down into the surface of the ceramic saucer. The saucer had a slight glaze to it. Currently not confirmed if it was a reaction with the glaze or the pottery itself.

SAM_0285 Another view of the cooled lead melt. The pedestal bulge can be seen to the left. SAM_0287 Interior of the pedestal structure after the furnace run. Small droplets of lead can be seen adhered to the inner wall.

SAM_0315 The lead mass removed. Areas where the pottery adhered to the lead can be seen. The central divot was due to a small amount of lead left in the pedestal from a previous run. The two lead masses did not merge together. Very clear concentric circles can be seen as the lead flowed inside the pedestal.

flowpath_3

The flow paths can be seen in the lead by the rings left as the flow cooled and moved. The bulge for the pedestal doorway can be seen along with how the lead took an easier path along the inside of the pedestal rather than flowing out.

SAM_0321

Lead melt set back into the inverted pedestal to show how it relates to the structure.

SAM_0322 Side view of the lead melt shows the uniform level of the melt mass. The top of the melt did not have the concentric rings the underside does.

SAM_0323 Other side of the melt mass.

This attempt on the lead based corium experiments showed what might be possible with a smaller volume fuel melt. A second run will be conducted using the higher end of the corium fuel melt volume estimates. The earlier glass melt experiment used a volume closer to the higher end volumes and showed a considerable flow out of the pedestal but was done at a much higher heat and time. The second lead melt experiment should help confirm some of the differences in behaviors between the two experiments. This smaller melt did show some affinity for working towards the pedestal opening. Additional experiments should help confirm this.

This article would not be possible without the extensive efforts of the SimplyInfo research team
Join the conversation at chat.simplyinfo.org

© 2011-2016 SimplyInfo.org, Fukuleaks.org All Rights Reserved Content cited, quoted etc. from other sources is under the respective rights of that content owner. If you are viewing this page on any website other than www.simplyinfo.org (or www.fukuleaks.org) it may be plagiarized, please let us know. If you wish to reproduce any of our content in full or in more than a phrase or quote, please contact us first to obtain permission.

Nancy Foust

Editor, SimplyInfo.org

Leave a Reply